Step by Step Instructions to Reflash to default.

You have to download and extract the FC Mptool.rar file, link is listed below.

Then you need to download and extract chipgenuis.rar file, link listed below.

The first step is to run the chipgenuis.exe to find the VID and PID numbers. Write these down. example VID 0001 PID 7778.

You do not need the serial or chip part number. If you find it is ok to keep.

Step1

If you have the USB plugged in, then you have to remove it from your computer.

Go to the folder where the FC MPtool.exe file is located.

Right click on the file and click on run as adminatrator.

If you see a window come up that says hub changed or something like that, your USB is still plugged into the computer DUH.

You will see the main program load up. If you look in the Usb Instructions.rar file you will see what that looks like.

(Note the UsbInstruction.rar is a xps file that Internet Explorer will view it.)

Step 2

Now you can plug in your Usb in your computer. You will see it displayed as a (308000: not specific) or something like that, relax it is OK.

Now click on the (setup) Button. It will ask for a password just leave blank and click (OK) and it will go past it.

Step 3

You will get a new window that shows up with the tabs (flash type), (mode), (Information), (bad block), (other).

Now you will start at flash type, you should see your chip listed automatically in the flash type box. Do not change it is your real chip set number. Mine was (MT29F32G08MAA).

Then set MP setup Optimize to (Capacity optimize) box.
Then set (Low level format) by clicking it.
Then set LLF to (Natural Check default).
Then set scan level to (Full scan 4) for a quick scan.
Then You are done do not touch any other setting.

Step 4

Go to the (mode) tab to set the settings.

Then set Mode to (pure disk).
Then set partition set (slide it to 0%).
Then set volume label to (kingston) but you can name it whatever you want it to be.It labels what it shows on your computer.
Then set disk sn (F19DB321) it also can be whatever you want it to be.
Then set led set to (ON) that sets the Usb light to come on when plugged into the computer.
That is it do not change anything else.

Step 5

Go to the (Inforamtion) tab to set the settings.

Then set the VID and PID numbers you got from the chipgenuis program. Mine where VID 001 and PID 7778.
Then set SCSI vender string (kingston) product string (datatraveler).
Then set USB vender string (kingston) product string (datatraveler).
Note It can be anything you want it to be. Usually you would put the name of your Usb.

Then set the SN set or serial number. Again you can use Random set or fixed and put (F19DB321) like I did with mine.


Step 6

Go to the (bad block) tab set the settings.

Then set bad block to (Auto check).
Then check the box (uninstall driver when close MP).
That is it.

Step 7

Go to the (other) tab to set the settings.

Then set compel specify flash to (default).
Then Hit the (OK) button on the button right hand corner you are done.

Step 7

You will go back to the main screen. You should see your Usb listed now with a long string of numbers and letters.

That is the fake flash they put on your Usb to make it say a larger size then it actually is.

Mine was (JS29F32G08AAMD1) to make it look like a 64Gb drive.

Now You Hit the (start) button.

It will erase and bad block twice in a row. Because they partitioned it into two drives.

Then it will bring it back to its original size. Mine USB went down to 2Gb. But now it is stable and useable.

When it says MP done successfully, then hit eject.

Then close the program. You should then unplug and replug your Usb. It will show the settings you put into it.

Now you have a new Usb. Enjoy.

Instruction How to ReFlash USB to Original

This is the Russian manual from the Russian website. It gives you a Quick look at how to setup the FC MPtool.exe that reflashes your USB back to default settings.

I will give a more detailed instructions after so do not worry about not getting it the first time.

http://www.4shared.com/file/224698855/518a5309/UsbInsrtuctions.html

ChipGenuis will show you your PID 7778 VID 0001 for your USB. My USB Kinsgston FC8308-1 is shown above.
You will need the PID and VID number for the settings in FC MPtool.exe program.

http://www.4shared.com/file/224703245/544bd14b/ChipGenius.html

The FC MPtool is the flash tool to bring back your fake USB to be stable and work properly.

http://www.4shared.com/file/224707449/d6127685/FC_MpTool_FC8308_FC8406_v20200.html

You will need all the files. The FC MPtool.exe will be extracted to a folder then click on only the FC MPtool.exe nothing else.

Now I will give step by step instructions on how to reflash that fake USB of yours before you through it in the garbage.

Fake Kingston USB 8Gb,16Gb,32Gb,etc Repair

I recently purchased a 64Gb kingston Usb for $28.00 canadian. Then I did a test to see if it was fake because of file errors will transfering files from computer to computer.

The test was H2Testw.exe witch failed showing a fake size of 43000Mb.

Later it flashed back to a 2Gb flash drive.(Kingston DataTraveler 200 64Gb)

http://www.ziggi.com.br/downloads/h2testw click on link, then click on button
(Clique par Biaxar) to download.

Do not worry you will hear a beep. Right Click on the yellow bar at the top and click on download file. It will be in a zip file.

Search for WinRAR to unzip it.
http://www.win-rar.com/affdownload/download.php

Now you can test your USB to see if it fails this test.

If it passes you are a happy costumer. If not then you have to reflash to the original
settings of the flash drive.